Dynamic DMA mapping
                        ===================

                 David S. Miller <davem@redhat.com>
                 Richard Henderson <rth@cygnus.com>
                  Jakub Jelinek <jakub@redhat.com>

This document describes the DMA mapping system in terms of the pci_
API.  For a similar API that works for generic devices, see
DMA-API.txt.

Most of the 64bit platforms have special hardware that translates bus
addresses (DMA addresses) into physical addresses.  This is similar to
how page tables and/or a TLB translates virtual addresses to physical
addresses on a CPU.  This is needed so that e.g. PCI devices can
access with a Single Address Cycle (32bit DMA address) any page in the
64bit physical address space.  Previously in Linux those 64bit
platforms had to set artificial limits on the maximum RAM size in the
system, so that the virt_to_bus() static scheme works (the DMA address
translation tables were simply filled on bootup to map each bus
address to the physical page __pa(bus_to_virt())).

So that Linux can use the dynamic DMA mapping, it needs some help from the
drivers, namely it has to take into account that DMA addresses should be
mapped only for the time they are actually used and unmapped after the DMA
transfer.

The following API will work of course even on platforms where no such
hardware exists, see e.g. include/asm-i386/pci.h for how it is implemented on
top of the virt_to_bus interface.

First of all, you should make sure

#include <linux/pci.h>

is in your driver. This file will obtain for you the definition of the
dma_addr_t (which can hold any valid DMA address for the platform)
type which should be used everywhere you hold a DMA (bus) address
returned from the DMA mapping functions.

                         What memory is DMA'able?

The first piece of information you must know is what kernel memory can
be used with the DMA mapping facilities.  There has been an unwritten
set of rules regarding this, and this text is an attempt to finally
write them down.

If you acquired your memory via the page allocator
(i.e. __get_free_page*()) or the generic memory allocators
(i.e. kmalloc() or kmem_cache_alloc()) then you may DMA to/from
that memory using the addresses returned from those routines.

This means specifically that you may _not_ use the memory/addresses
returned from vmalloc() for DMA.  It is possible to DMA to the
_underlying_ memory mapped into a vmalloc() area, but this requires
walking page tables to get the physical addresses, and then
translating each of those pages back to a kernel address using
something like __va().  [ EDIT: Update this when we integrate
Gerd Knorr's generic code which does this. ]

This rule also means that you may not use kernel image addresses
(ie. items in the kernel's data/text/bss segment, or your driver's)
nor may you use kernel stack addresses for DMA.  Both of these items
might be mapped somewhere entirely different than the rest of physical
memory.

Also, this means that you cannot take the return of a kmap()
call and DMA to/from that.  This is similar to vmalloc().

What about block I/O and networking buffers?  The block I/O and
networking subsystems make sure that the buffers they use are valid
for you to DMA from/to.

                        DMA addressing limitations

Does your device have any DMA addressing limitations?  For example, is
your device only capable of driving the low order 24-bits of address
on the PCI bus for SAC DMA transfers?  If so, you need to inform the
PCI layer of this fact.

By default, the kernel assumes that your device can address the full
32-bits in a SAC cycle.  For a 64-bit DAC capable device, this needs
to be increased.  And for a device with limitations, as discussed in
the previous paragraph, it needs to be decreased.

pci_alloc_consistent() by default will return 32-bit DMA addresses.
PCI-X specification requires PCI-X devices to support 64-bit
addressing (DAC) for all transactions. And at least one platform (SGI
SN2) requires 64-bit consistent allocations to operate correctly when
the IO bus is in PCI-X mode. Therefore, like with pci_set_dma_mask(),
it's good practice to call pci_set_consistent_dma_mask() to set the
appropriate mask even if your device only supports 32-bit DMA
(default) and especially if it's a PCI-X device.

For correct operation, you must interrogate the PCI layer in your
device probe routine to see if the PCI controller on the machine can
properly support the DMA addressing limitation your device has.  It is
good style to do this even if your device holds the default setting,
because this shows that you did think about these issues wrt. your
device.

The query is performed via a call to pci_set_dma_mask():

        int pci_set_dma_mask(struct pci_dev *pdev, u64 device_mask);

The query for consistent allocations is performed via a a call to
pci_set_consistent_dma_mask():

        int pci_set_consistent_dma_mask(struct pci_dev *pdev, u64 device_mask);

Here, pdev is a pointer to the PCI device struct of your device, and
device_mask is a bit mask describing which bits of a PCI address your
device supports.  It returns zero if your card can perform DMA
properly on the machine given the address mask you provided.

If it returns non-zero, your device can not perform DMA properly on
this platform, and attempting to do so will result in undefined
behavior.  You must either use a different mask, or not use DMA.

This means that in the failure case, you have three options:

1) Use another DMA mask, if possible (see below).
2) Use some non-DMA mode for data transfer, if possible.
3) Ignore this device and do not initialize it.

It is recommended that your driver print a kernel KERN_WARNING message
when you end up performing either #2 or #3.  In this manner, if a user
of your driver reports that performance is bad or that the device is not
even detected, you can ask them for the kernel messages to find out
exactly why.

The standard 32-bit addressing PCI device would do something like
this:

        if (pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
                printk(KERN_WARNING
                       "mydev: No suitable DMA available.\n");
                goto ignore_this_device;
        }

Another common scenario is a 64-bit capable device.  The approach
here is to try for 64-bit DAC addressing, but back down to a
32-bit mask should that fail.  The PCI platform code may fail the
64-bit mask not because the platform is not capable of 64-bit
addressing.  Rather, it may fail in this case simply because
32-bit SAC addressing is done more efficiently than DAC addressing.
Sparc64 is one platform which behaves in this way.

Here is how you would handle a 64-bit capable device which can drive
all 64-bits when accessing streaming DMA:

        int using_dac;

        if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
                using_dac = 1;
        } else if (!pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
                using_dac = 0;
        } else {
                printk(KERN_WARNING
                       "mydev: No suitable DMA available.\n");
                goto ignore_this_device;
        }

If a card is capable of using 64-bit consistent allocations as well,
the case would look like this:

        int using_dac, consistent_using_dac;

        if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
                using_dac = 1;
                consistent_using_dac = 1;
                pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
        } else if (!pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
                using_dac = 0;
                consistent_using_dac = 0;
                pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
        } else {
                printk(KERN_WARNING
                       "mydev: No suitable DMA available.\n");
                goto ignore_this_device;
        }

pci_set_consistent_dma_mask() will always be able to set the same or a
smaller mask as pci_set_dma_mask(). However for the rare case that a
device driver only uses consistent allocations, one would have to
check the return value from pci_set_consistent_dma_mask().

If your 64-bit device is going to be an enormous consumer of DMA
mappings, this can be problematic since the DMA mappings are a
finite resource on many platforms.  Please see the "DAC Addressing
for Address Space Hungry Devices" section near the end of this
document for how to handle this case.

Finally, if your device can only drive the low 24-bits of
address during PCI bus mastering you might do something like:

        if (pci_set_dma_mask(pdev, 0x00ffffff)) {
                printk(KERN_WARNING
                       "mydev: 24-bit DMA addressing not available.\n");
                goto ignore_this_device;
        }

When pci_set_dma_mask() is successful, and returns zero, the PCI layer
saves away this mask you have provided.  The PCI layer will use this
information later when you make DMA mappings.

There is a case which we are aware of at this time, which is worth
mentioning in this documentation.  If your device supports multiple
functions (for example a sound card provides playback and record
functions) and the various different functions have _different_
DMA addressing limitations, you may wish to probe each mask and
only provide the functionality which the machine can handle.  It
is important that the last call to pci_set_dma_mask() be for the 
most specific mask.

Here is pseudo-code showing how this might be done:

        #define PLAYBACK_ADDRESS_BITS   DMA_32BIT_MASK
        #define RECORD_ADDRESS_BITS     0x00ffffff

        struct my_sound_card *card;
        struct pci_dev *pdev;

        ...
        if (!pci_set_dma_mask(pdev, PLAYBACK_ADDRESS_BITS)) {
                card->playback_enabled = 1;
        } else {
                card->playback_enabled = 0;
                printk(KERN_WARN "%s: Playback disabled due to DMA limitations.\n",
                       card->name);
        }
        if (!pci_set_dma_mask(pdev, RECORD_ADDRESS_BITS)) {
                card->record_enabled = 1;
        } else {
                card->record_enabled = 0;
                printk(KERN_WARN "%s: Record disabled due to DMA limitations.\n",
                       card->name);
        }

A sound card was used as an example here because this genre of PCI
devices seems to be littered with ISA chips given a PCI front end,
and thus retaining the 16MB DMA addressing limitations of ISA.

                        Types of DMA mappings

There are two types of DMA mappings:

- Consistent DMA mappings which are usually mapped at driver
  initialization, unmapped at the end and for which the hardware should
  guarantee that the device and the CPU can access the data
  in parallel and will see updates made by each other without any
  explicit software flushing.

  Think of "consistent" as "synchronous" or "coherent".

  The current default is to return consistent memory in the low 32
  bits of the PCI bus space.  However, for future compatibility you
  should set the consistent mask even if this default is fine for your
  driver.

  Good examples of what to use consistent mappings for are:

        - Network card DMA ring descriptors.
        - SCSI adapter mailbox command data structures.
        - Device firmware microcode executed out of
          main memory.

  The invariant these examples all require is that any CPU store
  to memory is immediately visible to the device, and vice
  versa.  Consistent mappings guarantee this.

  IMPORTANT: Consistent DMA memory does not preclude the usage of
             proper memory barriers.  The CPU may reorder stores to
             consistent memory just as it may normal memory.  Example:
             if it is important for the device to see the first word
             of a descriptor updated before the second, you must do
             something like:

                desc->word0 = address;
                wmb();
                desc->word1 = DESC_VALID;

             in order to get correct behavior on all platforms.

- Streaming DMA mappings which are usually mapped for one DMA transfer,
  unmapped right after it (unless you use pci_dma_sync_* below) and for which
  hardware can optimize for sequential accesses.

  This of "streaming" as "asynchronous" or "outside the coherency
  domain".

  Good examples of what to use streaming mappings for are:

        - Networking buffers transmitted/received by a device.
        - Filesystem buffers written/read by a SCSI device.

  The interfaces for using this type of mapping were designed in
  such a way that an implementation can make whatever performance
  optimizations the hardware allows.  To this end, when using
  such mappings you must be explicit about what you want to happen.

Neither type of DMA mapping has alignment restrictions that come
from PCI, although some devices may have such restrictions.

                 Using Consistent DMA mappings.

To allocate and map large (PAGE_SIZE or so) consistent DMA regions,
you should do:

        dma_addr_t dma_handle;

        cpu_addr = pci_alloc_consistent(dev, size, &dma_handle);

where dev is a struct pci_dev *. You should pass NULL for PCI like buses
where devices don't have struct pci_dev (like ISA, EISA).  This may be
called in interrupt context. 

This argument is needed because the DMA translations may be bus
specific (and often is private to the bus which the device is attached
to).

Size is the length of the region you want to allocate, in bytes.

This routine will allocate RAM for that region, so it acts similarly to
__get_free_pages (but takes size instead of a page order).  If your
driver needs regions sized smaller than a page, you may prefer using
the pci_pool interface, described below.

The consistent DMA mapping interfaces, for non-NULL dev, will by
default return a DMA address which is SAC (Single Address Cycle)
addressable.  Even if the device indicates (via PCI dma mask) that it
may address the upper 32-bits and thus perform DAC cycles, consistent
allocation will only return > 32-bit PCI addresses for DMA if the
consistent dma mask has been explicitly changed via
pci_set_consistent_dma_mask().  This is true of the pci_pool interface
as well.

pci_alloc_consistent returns two values: the virtual address which you
can use to access it from the CPU and dma_handle which you pass to the
card.

The cpu return address and the DMA bus master address are both
guaranteed to be aligned to PAGE_SIZE.

To unmap and free such a DMA region, you call:

        pci_free_consistent(dev, size, cpu_addr, dma_handle);

where dev, size are the same as in the above call and cpu_addr and
dma_handle are the values pci_alloc_consistent returned to you.
This function may not be called in interrupt context.

If your driver needs lots of smaller memory regions, you can write
custom code to subdivide pages returned by pci_alloc_consistent,
or you can use the pci_pool API to do that.  A pci_pool is like
a kmem_cache, but it uses pci_alloc_consistent not __get_free_pages.
Also, it understands common hardware constraints for alignment,
like queue heads needing to be aligned on N byte boundaries.

Create a pci_pool like this:

        struct pci_pool *pool;

        pool = pci_pool_create(name, dev, size, align, alloc);

The "name" is for diagnostics (like a kmem_cache name); dev and size
are as above.  The device's hardware alignment requirement for this
type of data is "align" (which is expressed in bytes, and must be a
power of two).  If your device has no boundary crossing restrictions,
pass 0 for alloc; passing 4096 says memory allocated from this pool
must not cross 4KByte boundaries (but at that time it may be better to
go for pci_alloc_consistent directly instead).

Allocate memory from a pci pool like this:

        cpu_addr = pci_pool_alloc(pool, flags, &dma_handle);

flags are SLAB_KERNEL if blocking is permitted (not in_interrupt nor
holding SMP locks), SLAB_ATOMIC otherwise.  Like pci_alloc_consistent,
this returns two values, cpu_addr and dma_handle.

Free memory that was allocated from a pci_pool like this:

        pci_pool_free(pool, cpu_addr, dma_handle);

where pool is what you passed to pci_pool_alloc, and cpu_addr and
dma_handle are the values pci_pool_alloc returned. This function
may be called in interrupt context.

Destroy a pci_pool by calling:

        pci_pool_destroy(pool);

Make sure you've called pci_pool_free for all memory allocated
from a pool before you destroy the pool. This function may not
be called in interrupt context.

                        DMA Direction

The interfaces described in subsequent portions of this document
take a DMA direction argument, which is an integer and takes on
one of the following values:

 PCI_DMA_BIDIRECTIONAL
 PCI_DMA_TODEVICE
 PCI_DMA_FROMDEVICE
 PCI_DMA_NONE

One should provide the exact DMA direction if you know it.

PCI_DMA_TODEVICE means "from main memory to the PCI device"
PCI_DMA_FROMDEVICE means "from the PCI device to main memory"
It is the direction in which the data moves during the DMA
transfer.

You are _strongly_ encouraged to specify this as precisely
as you possibly can.

If you absolutely cannot know the direction of the DMA transfer,
specify PCI_DMA_BIDIRECTIONAL.  It means that the DMA can go in
either direction.  The platform guarantees that you may legally
specify this, and that it will work, but this may be at the
cost of performance for example.

The value PCI_DMA_NONE is to be used for debugging.  One can
hold this in a data structure before you come to know the
precise direction, and this will help catch cases where your
direction tracking logic has failed to set things up properly.

Another advantage of specifying this value precisely (outside of
potential platform-specific optimizations of such) is for debugging.
Some platforms actually have a write permission boolean which DMA
mappings can be marked with, much like page protections in the user
program address space.  Such platforms can and do report errors in the
kernel logs when the PCI controller hardware detects violation of the
permission setting.

Only streaming mappings specify a direction, consistent mappings
implicitly have a direction attribute setting of
PCI_DMA_BIDIRECTIONAL.

The SCSI subsystem provides mechanisms for you to easily obtain
the direction to use, in the SCSI command:

        scsi_to_pci_dma_dir(SCSI_DIRECTION)

Where SCSI_DIRECTION is obtained from the 'sc_data_direction'
member of the SCSI command your driver is working on.  The
mentioned interface above returns a value suitable for passing
into the streaming DMA mapping interfaces below.

For Networking drivers, it's a rather simple affair.  For transmit
packets, map/unmap them with the PCI_DMA_TODEVICE direction
specifier.  For receive packets, just the opposite, map/unmap them
with the PCI_DMA_FROMDEVICE direction specifier.

                  Using Streaming DMA mappings

The streaming DMA mapping routines can be called from interrupt
context.  There are two versions of each map/unmap, one which will
map/unmap a single memory region, and one which will map/unmap a
scatterlist.

To map a single region, you do:

        struct pci_dev *pdev = mydev->pdev;
        dma_addr_t dma_handle;
        void *addr = buffer->ptr;
        size_t size = buffer->len;

        dma_handle = pci_map_single(dev, addr, size, direction);

and to unmap it:

        pci_unmap_single(dev, dma_handle, size, direction);

You should call pci_unmap_single when the DMA activity is finished, e.g.
from the interrupt which told you that the DMA transfer is done.

Using cpu pointers like this for single mappings has a disadvantage,
you cannot reference HIGHMEM memory in this way.  Thus, there is a
map/unmap interface pair akin to pci_{map,unmap}_single.  These
interfaces deal with page/offset pairs instead of cpu pointers.
Specifically:

        struct pci_dev *pdev = mydev->pdev;
        dma_addr_t dma_handle;
        struct page *page = buffer->page;
        unsigned long offset = buffer->offset;
        size_t size = buffer->len;

        dma_handle = pci_map_page(dev, page, offset, size, direction);

        ...

        pci_unmap_page(dev, dma_handle, size, direction);

Here, "offset" means byte offset within the given page.

With scatterlists, you map a region gathered from several regions by:

        int i, count = pci_map_sg(dev, sglist, nents, direction);
        struct scatterlist *sg;

        for (i = 0, sg = sglist; i < count; i++, sg++) {
                hw_address[i] = sg_dma_address(sg);
                hw_len[i] = sg_dma_len(sg);
        }

where nents is the number of entries in the sglist.

The implementation is free to merge several consecutive sglist entries
into one (e.g. if DMA mapping is done with PAGE_SIZE granularity, any
consecutive sglist entries can be merged into one provided the first one
ends and the second one starts on a page boundary - in fact this is a huge
advantage for cards which either cannot do scatter-gather or have very
limited number of scatter-gather entries) and returns the actual number
of sg entries it mapped them to. On failure 0 is returned.

Then you should loop count times (note: this can be less than nents times)
and use sg_dma_address() and sg_dma_len() macros where you previously
accessed sg->address and sg->length as shown above.

To unmap a scatterlist, just call:

        pci_unmap_sg(dev, sglist, nents, direction);

Again, make sure DMA activity has already finished.

PLEASE NOTE:  The 'nents' argument to the pci_unmap_sg call must be
              the _same_ one you passed into the pci_map_sg call,
              it should _NOT_ be the 'count' value _returned_ from the
              pci_map_sg call.

Every pci_map_{single,sg} call should have its pci_unmap_{single,sg}
counterpart, because the bus address space is a shared resource (although
in some ports the mapping is per each BUS so less devices contend for the
same bus address space) and you could render the machine unusable by eating
all bus addresses.

If you need to use the same streaming DMA region multiple times and touch
the data in between the DMA transfers, the buffer needs to be synced
properly in order for the cpu and device to see the most uptodate and
correct copy of the DMA buffer.

So, firstly, just map it with pci_map_{single,sg}, and after each DMA
transfer call either:

        pci_dma_sync_single_for_cpu(dev, dma_handle, size, direction);

or:

        pci_dma_sync_sg_for_cpu(dev, sglist, nents, direction);

as appropriate.

Then, if you wish to let the device get at the DMA area again,
finish accessing the data with the cpu, and then before actually
giving the buffer to the hardware call either:

        pci_dma_sync_single_for_device(dev, dma_handle, size, direction);

or:

        pci_dma_sync_sg_for_device(dev, sglist, nents, direction);

as appropriate.

After the last DMA transfer call one of the DMA unmap routines
pci_unmap_{single,sg}. If you don't touch the data from the first pci_map_*
call till pci_unmap_*, then you don't have to call the pci_dma_sync_*
routines at all.

Here is pseudo code which shows a situation in which you would need
to use the pci_dma_sync_*() interfaces.

        my_card_setup_receive_buffer(struct my_card *cp, char *buffer, int len)
        {
                dma_addr_t mapping;

                mapping = pci_map_single(cp->pdev, buffer, len, PCI_DMA_FROMDEVICE);

                cp->rx_buf = buffer;
                cp->rx_len = len;
                cp->rx_dma = mapping;

                give_rx_buf_to_card(cp);
        }

        ...

        my_card_interrupt_handler(int irq, void *devid, struct pt_regs *regs)
        {
                struct my_card *cp = devid;

                ...
                if (read_card_status(cp) == RX_BUF_TRANSFERRED) {
                        struct my_card_header *hp;

                        /* Examine the header to see if we wish
                         * to accept the data.  But synchronize
                         * the DMA transfer with the CPU first
                         * so that we see updated contents.
                         */
                        pci_dma_sync_single_for_cpu(cp->pdev, cp->rx_dma,
                                                    cp->rx_len,
                                                    PCI_DMA_FROMDEVICE);

                        /* Now it is safe to examine the buffer. */
                        hp = (struct my_card_header *) cp->rx_buf;
                        if (header_is_ok(hp)) {
                                pci_unmap_single(cp->pdev, cp->rx_dma, cp->rx_len,
                                                 PCI_DMA_FROMDEVICE);
                                pass_to_upper_layers(cp->rx_buf);
                                make_and_setup_new_rx_buf(cp);
                        } else {
                                /* Just sync the buffer and give it back
                                 * to the card.
                                 */
                                pci_dma_sync_single_for_device(cp->pdev,
                                                               cp->rx_dma,
                                                               cp->rx_len,
                                                               PCI_DMA_FROMDEVICE);
                                give_rx_buf_to_card(cp);
                        }
                }
        }

Drivers converted fully to this interface should not use virt_to_bus any
longer, nor should they use bus_to_virt. Some drivers have to be changed a
little bit, because there is no longer an equivalent to bus_to_virt in the
dynamic DMA mapping scheme - you have to always store the DMA addresses
returned by the pci_alloc_consistent, pci_pool_alloc, and pci_map_single
calls (pci_map_sg stores them in the scatterlist itself if the platform
supports dynamic DMA mapping in hardware) in your driver structures and/or
in the card registers.

All PCI drivers should be using these interfaces with no exceptions.
It is planned to completely remove virt_to_bus() and bus_to_virt() as
they are entirely deprecated.  Some ports already do not provide these
as it is impossible to correctly support them.

                64-bit DMA and DAC cycle support

Do you understand all of the text above?  Great, then you already
know how to use 64-bit DMA addressing under Linux.  Simply make
the appropriate pci_set_dma_mask() calls based upon your cards
capabilities, then use the mapping APIs above.

It is that simple.

Well, not for some odd devices.  See the next section for information
about that.

        DAC Addressing for Address Space Hungry Devices

There exists a class of devices which do not mesh well with the PCI
DMA mapping API.  By definition these "mappings" are a finite
resource.  The number of total available mappings per bus is platform
specific, but there will always be a reasonable amount.

What is "reasonable"?  Reasonable means that networking and block I/O
devices need not worry about using too many mappings.

As an example of a problematic device, consider compute cluster cards.
They can potentially need to access gigabytes of memory at once via
DMA.  Dynamic mappings are unsuitable for this kind of access pattern.

To this end we've provided a small API by which a device driver
may use DAC cycles to directly address all of physical memory.
Not all platforms support this, but most do.  It is easy to determine
whether the platform will work properly at probe time.

First, understand that there may be a SEVERE performance penalty for
using these interfaces on some platforms.  Therefore, you MUST only
use these interfaces if it is absolutely required.  %99 of devices can
use the normal APIs without any problems.

Note that for streaming type mappings you must either use these
interfaces, or the dynamic mapping interfaces above.  You may not mix
usage of both for the same device.  Such an act is illegal and is
guaranteed to put a banana in your tailpipe.

However, consistent mappings may in fact be used in conjunction with
these interfaces.  Remember that, as defined, consistent mappings are
always going to be SAC addressable.

The first thing your driver needs to do is query the PCI platform
layer with your devices DAC addressing capabilities:

        int pci_dac_set_dma_mask(struct pci_dev *pdev, u64 mask);

This routine behaves identically to pci_set_dma_mask.  You may not
use the following interfaces if this routine fails.

Next, DMA addresses using this API are kept track of using the
dma64_addr_t type.  It is guaranteed to be big enough to hold any
DAC address the platform layer will give to you from the following
routines.  If you have consistent mappings as well, you still
use plain dma_addr_t to keep track of those.

All mappings obtained here will be direct.  The mappings are not
translated, and this is the purpose of this dialect of the DMA API.

All routines work with page/offset pairs.  This is the _ONLY_ way to 
portably refer to any piece of memory.  If you have a cpu pointer
(which may be validly DMA'd too) you may easily obtain the page
and offset using something like this:

        struct page *page = virt_to_page(ptr);
        unsigned long offset = offset_in_page(ptr);

Here are the interfaces:

        dma64_addr_t pci_dac_page_to_dma(struct pci_dev *pdev,
                                         struct page *page,
                                         unsigned long offset,
                                         int direction);

The DAC address for the tuple PAGE/OFFSET are returned.  The direction
argument is the same as for pci_{map,unmap}_single().  The same rules
for cpu/device access apply here as for the streaming mapping
interfaces.  To reiterate:

        The cpu may touch the buffer before pci_dac_page_to_dma.
        The device may touch the buffer after pci_dac_page_to_dma
        is made, but the cpu may NOT.

When the DMA transfer is complete, invoke:

        void pci_dac_dma_sync_single_for_cpu(struct pci_dev *pdev,
                                             dma64_addr_t dma_addr,
                                             size_t len, int direction);

This must be done before the CPU looks at the buffer again.
This interface behaves identically to pci_dma_sync_{single,sg}_for_cpu().

And likewise, if you wish to let the device get back at the buffer after
the cpu has read/written it, invoke:

        void pci_dac_dma_sync_single_for_device(struct pci_dev *pdev,
                                                dma64_addr_t dma_addr,
                                                size_t len, int direction);

before letting the device access the DMA area again.

If you need to get back to the PAGE/OFFSET tuple from a dma64_addr_t
the following interfaces are provided:

        struct page *pci_dac_dma_to_page(struct pci_dev *pdev,
                                         dma64_addr_t dma_addr);
        unsigned long pci_dac_dma_to_offset(struct pci_dev *pdev,
                                            dma64_addr_t dma_addr);

This is possible with the DAC interfaces purely because they are
not translated in any way.

                Optimizing Unmap State Space Consumption

On many platforms, pci_unmap_{single,page}() is simply a nop.
Therefore, keeping track of the mapping address and length is a waste
of space.  Instead of filling your drivers up with ifdefs and the like
to "work around" this (which would defeat the whole purpose of a
portable API) the following facilities are provided.

Actually, instead of describing the macros one by one, we'll
transform some example code.

1) Use DECLARE_PCI_UNMAP_{ADDR,LEN} in state saving structures.
   Example, before:

        struct ring_state {
                struct sk_buff *skb;
                dma_addr_t mapping;
                __u32 len;
        };

   after:

        struct ring_state {
                struct sk_buff *skb;
                DECLARE_PCI_UNMAP_ADDR(mapping)
                DECLARE_PCI_UNMAP_LEN(len)
        };

   NOTE: DO NOT put a semicolon at the end of the DECLARE_*()
         macro.

2) Use pci_unmap_{addr,len}_set to set these values.
   Example, before:

        ringp->mapping = FOO;
        ringp->len = BAR;

   after:

        pci_unmap_addr_set(ringp, mapping, FOO);
        pci_unmap_len_set(ringp, len, BAR);

3) Use pci_unmap_{addr,len} to access these values.
   Example, before:

        pci_unmap_single(pdev, ringp->mapping, ringp->len,
                         PCI_DMA_FROMDEVICE);

   after:

        pci_unmap_single(pdev,
                         pci_unmap_addr(ringp, mapping),
                         pci_unmap_len(ringp, len),
                         PCI_DMA_FROMDEVICE);

It really should be self-explanatory.  We treat the ADDR and LEN
separately, because it is possible for an implementation to only
need the address in order to perform the unmap operation.

                        Platform Issues

If you are just writing drivers for Linux and do not maintain
an architecture port for the kernel, you can safely skip down
to "Closing".

1) Struct scatterlist requirements.

   Struct scatterlist must contain, at a minimum, the following
   members:

        struct page *page;
        unsigned int offset;
        unsigned int length;

   The base address is specified by a "page+offset" pair.

   Previous versions of struct scatterlist contained a "void *address"
   field that was sometimes used instead of page+offset.  As of Linux
   2.5., page+offset is always used, and the "address" field has been
   deleted.

2) More to come...

                        Handling Errors

DMA address space is limited on some architectures and an allocation
failure can be determined by:

- checking if pci_alloc_consistent returns NULL or pci_map_sg returns 0

- checking the returned dma_addr_t of pci_map_single and pci_map_page
  by using pci_dma_mapping_error():

        dma_addr_t dma_handle;

        dma_handle = pci_map_single(dev, addr, size, direction);
        if (pci_dma_mapping_error(dma_handle)) {
                /*
                 * reduce current DMA mapping usage,
                 * delay and try again later or
                 * reset driver.
                 */
        }

                           Closing

This document, and the API itself, would not be in it's current
form without the feedback and suggestions from numerous individuals.
We would like to specifically mention, in no particular order, the
following people:

        Russell King <rmk@arm.linux.org.uk>
        Leo Dagum <dagum@barrel.engr.sgi.com>
        Ralf Baechle <ralf@oss.sgi.com>
        Grant Grundler <grundler@cup.hp.com>
        Jay Estabrook <Jay.Estabrook@compaq.com>
        Thomas Sailer <sailer@ife.ee.ethz.ch>
        Andrea Arcangeli <andrea@suse.de>
        Jens Axboe <axboe@suse.de>
        David Mosberger-Tang <davidm@hpl.hp.com>